Recover Tactical Picatinny Rail for Glock, Glock MOS, S&W Shield 9mm, SW40, Sig P365 (Must Select Your Model Below), Easy Install, No Mods Required

This fits my Sig Sauer P365X(L) with Wilson Combat grip module. No problems. It fits snug and secure.I was a little concerned with it being fastened with only a single screw, but it grips nicely onto grip module such that the screw really only needs to hold the two halves tightly together. It holds securely / reliably. It seems well made / sturdy / durable.I got this to be able to mount a Mantis X3 for training, and it works fine for that purpose. Note that I'm NOT using this to mount a weapon light for EDC. I have a light that mounts directly to the grip module. So, I'm using this ONLY when training with the Mantis X. I presume this would hold up under EDC use, but I can't confirm that.Since I'm putting it on and taking it off frequently for training, it seems inevitable that I'll lose the nut at some point. I appreciate that this came with an extra nut & screw.I was a little concerned that it would throw off the weight balance by moving the attachment further away (down) from the slide, but it seems fine - not too thick.

Fits my G26 perfectly. Easy to attach. Rail fits my light perfectly. Solid build.

Despite the horrible experience with the M9/92FS Recover rail, this one for the G17 works very well. Snug fit, but I'd argue that this is better [in some ways] than having a Gen3-5 rail. This rail accommodates for the angle of the frame as it graduates towards the muzzle so it can essentially make the rail parallel to the slide. On Glock rails however, they tend to pignose and aren't the most study rails. I would argue this Recover rail creates a more stable platform than the Gen3-5's.Easy to install and it doesn't seem to damage the frame at all. Lights will sit very slightly more forward on Glock-specific lights/attachments, but in other cases, the ability to use a 1913 rail on a Glock makes it sit about where it would normally. In all cases, however, the light will sit lower down because the attachment point is about a half inch lower than a Glock rail would be. In some cases again though, this actually helps. Worth the money, and if you're a Gen 1/2 owner or loyalist, this is a great addition that makes the frame even sturdier and IMO looks better than a Glock rail. FYI I did for the hell of it try it fit this on my G21 Gen2 and it wouldn't fit. As others have said, it would work with some time and a Dremel, but I personally wouldn't try it unless you're desperate and have patience to remove the right amount of material from what would be at least 4 areas. I did sand some areas with 1500 grit sandpaper just to smooth out some areas that the slide will touch, but it was barely needed--if at all. Thumbs up.

Other than it being plastic and looks to be 3D printed , it works kinda well as intended I have a GL 26 Gen 3 and it fit perfect just have to clip in place with the trigger and screw in place with tiny screws and afterwards I put on a olight balor RL mini and it fit pretty snug , you can adjust the flash as needed forward or back. Overall had a little issue trying to clip it on , instructions need to be a little more clear but overall perfect for what you buying and paying for

**UPDATED please read all** I must have ended up with a defective one. Yes it is extremely easy to install, and yes it is very affordable. Also the construction seems to be of sturdy quality. However, on one side of the gun once mounted, it fits slightly crooked and misaligned. Almost like warped from manufacturing and is slight off. The side profile fits on one side and seems to flow flawlessly with the slide, while on the warped side it dips down towards the barrel..... I really wanted to give this a great review as I really liked having the option. Plus it does look really nice on the gun. ** UPDATE** Gunsmith was able to file some material down, and heat the material to fix the warped side. Fits much better just slightly loose. However, the slide does not jam now and the one side no longer bulges out. Spoke with another individual who also purchased for his and it mounted right on with no issues. Reached out to company just in case mine was a fluke. Company responded back almost instantly and is sending a new one at no cost as this is not a known issue. Also, they reviewed pictures of what the Gunsmith shaved off and were concerned about the material the gunsmith removed. If you have any issues at all please reach out to company first! They are responsive and truly care about the product they put out. Would highly recommend!!! *** Just got new one in mail, mounted up perfectly, no issues!!!

I wasn’t so impressed when I open the box and found these two little pieces of it when I assemble them on the gun it was actually a stunning transformation. I guess most polymers don’t look impressive when you’re looking on the inside of them but when is assembled it’s amazing. this thing has such an excellent fit and finish it looks like it’s part of the gun.All the sudden I’m freed up from Sig’s proprietary playground and I can put out any accessory on my rail.The only downside is it’s going to add a little bit of width to your pistol, and more so when you actually attach an accessory. If you own one of these it’s probably your carry gun so Wednesday is a significant factor.However that’s almost like complaining that a full tank of gas makes your car way more. That’s kind of the price of doing business in the accessory category.The screw is big and enough the attachment point seems very solid and anything I’ve attached to it has held on and kept it zero so absolutely a perfect and affordable a way to expand your 365, rather than buying the really overpriced proprietary accessories.

I returned this item. It fit the G43 perfectly but adding the optic didn’t look or feel right so I went a different direction. Product was good and return was easy.